Reman Howo 371 6×4 Tractor Head
Many buyers confuse remanufacturing, overhaul and cosmetic repaint work. This certified reman Sinotruk tractor truck follows full-system reman standards, instead of only fixing obvious faults or refreshing exterior appearance.
Reman Tractor Head for Sale Description
- Before investing in a heavy tractor, it is vital to understand the gap between remanufacturing, overhaul and cosmetic refurbishment.
- Overhaul only repairs failed parts to get the vehicle running, while cosmetic refurbishment focuses only on paint and exterior look, with no deep inspection of internal wear.



- REMAN ROAD certified reman Sinotruk tractor truck requires full disassembly of all core assemblies, systematic component screening, performance calibration and end-to-end validation.
- Reman tractor head for sale carries a systematic whole-vehicle warranty, rather than limited coverage only for one repaired component.




Specification Table
- Model: Certified Reman Sinotruk Tractor Truck Howo 6×4 371
- Engine: Complete teardown, wear measurement, limit parts renewed, bench load tested
- Transmission: Disassembled inspection, gear clearance calibrated, lubrication circuit cleaned, bench validated
- Chassis Frame: Visual + NDT crack inspection; fatigue defects rejected, fasteners retorqued to factory torque
- Suspension: Leaf spring / shock absorber inspection, fatigue units replaced, axle load balance checked
- Tires: 12.00R20 heavy-duty off-road tires, wheel hubs serviced and bearings renewed
- Brake System: Full air circuit overhaul, valves & friction parts renewed, axle brake balance calibrated
- Steering Assembly: Disassembled, worn bushings replaced, free play adjusted to factory specification
- Fuel & Air System: Tanks cleaned, filters replaced, air circuit leak tested, fuel delivery stability verified
- Electrical & CAN Bus: Harness restored to factory layout, faulty sensors replaced, all signal communication tested
- Cabin: Fully disassembled, corrosion checked, wiring restored, all gauges & controls tested, refinished
Truck Remanufacturing Process
- Core Screening: Reject damaged cores; record valid core by VIN.
- Full Teardown & Cleaning: Strip tractor into separate components and clean all parts.
- Grading & NDT Test: Sort parts for reuse / repair / scrap; inspect frame for hidden cracks.
- Parts Renewal: Replace failed parts and machine repairable components.
- Reassembly & Bench Test: Rebuild assemblies and test powertrain, brake systems.
- Whole Vehicle Check & Road Test: Adjust all systems and run loaded road validation.
- Documentation & Handover: Generate traceability records and issue reman certificate.
Why Structural Integrity Is The Top Priority For Reman Tractor Head?
- Tractors bear huge pulling loads and dynamic shock stress far beyond many other heavy vehicles.
- Hidden frame cracks and structural fatigue often cannot be spotted by simple visual checks.
- NDT non-destructive testing is mandatory for all load-bearing frame and bracket components in our workflow.
- A structurally sound frame is the foundation of safe, long-running heavy haulage.
Traceability Systems: Transparency For Cross-Border Buyers
- Traceability links every inspection, test and component replacement record directly to the vehicle VIN.
- Buyers can review the full reman history instead of relying on verbal descriptions of vehicle condition.
- These records support internal fleet management, third-party audits and cross-border compliance requirements.
- Permanent documentation also adds value if you choose to resell the tractor in the future.
RFQ
- Q1: What is your overall core sourcing strategy for reman tractor head for sale cores, and how do you avoid accident-damaged stock?
A: We source cores from decommissioned commercial fleets with verifiable service history. Every candidate core goes through accident record checks, frame visual inspection and preliminary NDT screening before purchase. Cores confirmed to have major crash or rollover damage are permanently rejected from our supply pool. - Q2: If a core passes pre-entry screening but hidden irreversible damage is uncovered during full disassembly, what is your formal process?
A: We immediately halt reman work on that core, notify you of the findings with inspection evidence, and remove this core from the order. We then present alternative pre-screened qualified cores matching the same model for your selection, or adjust the delivery schedule accordingly. - Q3: Do you separate core stock by original working background, such as highway haulage vs heavy construction site use?
A: Yes, we categorise cores by their historical operating environment. Cores that previously worked on harsh construction sites receive extra structural inspection during reman, and we disclose this background in the traceability file for your reference. - Q4: Is there a maximum age or service life cap you apply for all tractor cores entering reman?
A: We do not use a fixed calendar age cap. The deciding factor is structural condition, fatigue level and repair history. An older core with light highway use and intact frame can qualify, while a younger core with heavy impact damage will be rejected. - Q5: Can we specify that our ordered tractors must only come from cores with highway-only previous usage?
A: Yes, you can add this requirement to your purchase specification. We will allocate matching cores and mark this condition in the traceability documentation for each delivered unit.



