Reman Heavy Howo 8×4 Dump Truck

Reman Heavy Dump Truck for Sale Description

• REMAN ROAD reman 8×4 dump truck provides larger cargo volume and higher rated payload than 6×4 tippers, reducing the total number of trips required to move the same amount of material.
• The multi-axle suspension and four heavy-duty axles are fully inspected and remanufactured to distribute weight evenly, protecting the chassis and improving stability under full payload.

• Every hydraulic, brake and power assembly is tested to OEM standards. For large earthmoving, quarry and infrastructure projects, REMAN ROAD reman 8×4 dump truck improves overall fleet productivity and shortens project schedules.

Specification Table

• Model: China Reman Howo Truck Dump 8×4
• Drive: 8×4, 12-wheel heavy-duty tipper, classic HOWO chassis
• Engine: Reman WD615 series diesel engine, full rebuild, dynamometer bench tested
• Displacement: 9.726L, inline 6-cylinder, turbo intercooled
• Transmission: Reman 10-speed manual gearbox, worn components replaced, load bench tested
• Clutch: New clutch assembly, hydraulic control system overhauled
• Front Axle: Reman steering axle, kingpin, bearings renewed, alignment calibrated
• Rear Axles: Reman double reduction heavy axles, crack detection, differential & bearings renewed
• Suspension: Multi-leaf spring, cracked springs replaced, bushings and shackles renewed
• Cargo Box: Reman tipper body, sandblasted and structural repaired. Hydraulic cylinder overhauled and cycle-tested
• Hydraulic System: Pump & valve rebuilt, seals and hoses replaced. Load lifting cycles validated
• Tires: 12.00R20 heavy-duty off-road tires, wheel hubs serviced and bearings renewed
• Brake System: WABCO air brake system, key components renewed, air tightness & braking performance tested
• Cabin: Classic HOWO cab, interior refurbished, seals and wiring renewed, water leak tested
• Cooling System: Radiator serviced, water pump inspected, hoses/thermostat replaced, pressure tested
• Steering: Reman power steering gear, tie rods & ball joints renewed, wheel alignment completed

Truck Remanufacturing Process

• Incoming Screening: Inspect base truck, test chassis frame for cracks. Reject units with serious structural damage.
• Full Disassembly: Strip vehicle into separate assemblies: engine, gearbox, axles, suspension, cab, cargo box and hydraulic systems.
• Cleaning & Inspection: Clean all parts, measure dimensions against OEM standards, classify reusable, repairable and scrap parts.
• Core Rebuild & Bench Test: Rebuild engine, transmission, axles and hydraulics. Replace all worn consumables and complete bench performance tests.
• Chassis Restoration: Sandblast frame, repair minor defects, apply anti-corrosion coating, renew suspension components.
• Reassembly: Assemble all parts following factory torque specs, reconnect hydraulic, pneumatic and electrical systems.
• Performance Validation: Run cold start, loaded road test, hydraulic lifting test, air brake test and full electrical inspection.
• Final Delivery Prep: Finish painting, export anti-rust treatment, compile all test and warranty documents.

Fleet Deployment Flexibility

The global heavy truck market has experienced significant supply chain disruptions in recent years. Ordering a brand-new dump truck can mean waiting several months—or even over a year—for delivery. In the fast-moving construction and mining industry, this delay can cost you project opportunities. A new contract requires immediate hauling capacity, and you cannot afford to pause operations waiting for vehicle delivery:

• REMAN ROAD reman heavy dump truck for sale are available from stock or with short production lead times. You can add trucks to your fleet and deploy them to job sites within weeks, not months.
• This agility allows you to respond quickly to new project awards, seasonal demand peaks or sudden fleet expansion needs. You are not dependent on new truck factory schedules.
• For project-based fleets, the ability to scale up quickly and start generating revenue is a critical commercial advantage that directly impacts your bottom line.

Operational Safety and Risk Reduction on Job Sites

Unmaintained or poorly refurbished trucks carry hidden mechanical risks. Brake fade, steering wear, hydraulic system failures and tire blowouts can lead to serious job site accidents. These incidents cause not only human injury risks but also equipment damage, project downtime, regulatory penalties and rising insurance premiums:

• REMAN ROAD reman 8×4 dump truck remanufacturing process thoroughly inspects, rebuilds and tests every critical safety system.
• The air brake system undergoes pressure testing and load braking verification. The steering system is fully overhauled and aligned. The hydraulic tipping system is cycle-tested under load. Every electrical component is checked.
• By eliminating hidden safety risks before the truck enters service, you create a safer operating environment for your drivers and job site personnel.
• Fewer safety incidents mean fewer work stoppages, lower insurance risk, better regulatory compliance and reduced liability exposure—all of which protect your fleet’s productivity and profitability.

RFQ

• Q: What special inspection work do you carry out for the 8×4 multi-axle chassis during remanufacturing?
  A: We conduct magnetic particle crack detection on the whole frame, especially on stress points of suspension brackets and axle mounting areas. All four axles are disassembled and inspected, and we check frame deformation to ensure it can bear the full rated payload safely. Frames with permanent bending or critical cracks will be rejected directly.
• Q: How do you test the multi-axle braking system of this reman heavy dump truck for sale after remanufacturing?
  A: The full WABCO air brake system is overhauled. We complete air tightness testing, load braking performance test and axle-by-axle brake balance calibration, to guarantee balanced braking response across all four axles under heavy load.
• Q: What is the maximum payload your reman 8×4 dump truck can safely carry?
  A: The safe rated payload is 30–35 tons, subject to local road transport regulations. The remanufactured chassis, axles and suspension are all restored to original factory load specifications to support this payload.
• Q: Can you strengthen the cargo box floor for highly abrasive rock and ore materials?
  A: Yes. We can install wear-resistant steel liners or thicken the box floor plate according to your working conditions, extending the service life of the cargo box under abrasive material transport.
• Q: What documents will be provided together with the reman heavy dump truck for sale for export customs clearance?
  A: We provide commercial invoice, packing list, vehicle QC report, component test records and warranty certificate, supporting your import customs declaration.
• Q: What is the typical lead time for one reman 8×4 dump truck?
  A: The remanufacturing cycle takes around 25–32 working days, plus 3–5 days for export anti-rust treatment and packaging. Bulk orders can be scheduled for batch delivery.